Aluminium Blue Water Cruiser Project
Under Construction & Unused
- Boot REF# · 220635
- LOA · 11.58m
- Jaar · 2012
- Constructie · Aluminium
- Onderwater profiel · lange keel
- Motor · 1 x diesel 80hp, Perkins M90 (2015)
- Ligplaats · Plymouth
Deze boot is uit de markt but here are some boats that are still For Sale
Extra Details
| Ontwerper | Ganley Yachts, New Zealand |
|---|---|
| Bouwer | Previous Owner, Isle of Wight |
| Ligplaats | Plymouth |
| Brandstof capaciteit | 800.0 ltr Total - 2 Tanks |
| Water capaciteit | 600.0 ltr Total - 5 Tanks |
| Inhoud vuilwatertank | 60.0 ltr Total - 1 Tanks |
Meganisch
| Motor | 1 x diesel 80hp |
|---|---|
| Engine merk en model | Perkins M90 (2015) |
| Motor uren |
motor1= 00 |
| Engine Cooled | Indirect |
| Stuur | tiller |
| Aandrijving | Schroefas |
| Brandstof verbruik (ong) | Niet bekend |
Perkins Factory reconditioned engine £5000
Engine hours = 0
New drive shaft
Batteries will be chargeable by engine & shore power
Possible to change steering from tiller to wheel - steering parts excluding wheel available.
Afmetingen
| LOA | 11.58m |
|---|---|
| LWL | 10.06m |
| Breedte | 3.35m |
| Minimum diepgang | 2.00m |
| Maximum diepgang | 2.00m |
| Waterverplaatsing | 5,000kg |
| Hoofdruimte | 1.91m |
| Opslag | Op de wal |
Electrische systemen
24 volt batterij,
Constructie
| Construction | Aluminium |
|---|---|
| Onderwater profiel | lange keel |
| Afwerking | Aluminium afwerking |
Displacement figure approximate.
The owner believes there is the following outstanding work to be done on this project:
'The engine installation needs to be finished including the exhaust system, fuel system and controls.
The shaft seal needs to be installed e.g. Tides marine seal.
The prop needs to be obtained.
The Ballast needs to be fitted, washer punchings (3 tons required) and then the bilge pumps etc. can be done (on board ready).
Weld on hand rails.
The wiring is all there ready for connection."
Accommodatie
| Handwasbakje | 1 |
|---|---|
| Hids | 1 hids (Handmatig) |
Double sink in galley
Heads fitted & plumbed with holding tank.
Accommodatie
| Wasbak | |
|---|---|
| Koelkast | |
| Waterdruk systeem | |
| Niet Rokers |
Double sink in galley
Heads fitted & plumbed with holding tank.
Dek uitrusting
| Deklijnen |
|---|
1 ankers
(Delta 20kg)
60.00m ketting
Veiligheids uitrusting
5 bilge pompen (1 handmatig / 4 electrisch)
Bilge pumps need to be fitted
Makelaars opmerking
This sturdy partially fitted out aluminium hull has the potential to become a fantastic blue water cruising vessel, power or sail.
The unique stern was originally constructed by the previous owner to house a salvage winch for retrieving treasure in the Pacific Ocean.
A great deal of the expensive internal work has already been carried out by a professional engineer. She comes fitted with an 80 hp Perkins M90 at a cost of £5k, which is fully reconditioned and unused from the Perkins factory. A new prop shaft is also fitted and she has plenty of brand new tankage fitted for fuel, water and a holding tank for waste.
The galley is partially fitted with a double sink and fridge. The heads/wet room is also a work in progress with a new toilet & sink whilst a shower still needs to be purchased & fitted.
All Tru Design skin fittings are ABYC approved & rated H-27 standard for aluminium hulls.
Also included are 4 electric bilge pumps plus 1 manual, a battery charger, fresh water pumps and chain plates if needed.
This is a great opportunity to acquire a very reasonably priced, unused, aluminium hull and to finish it to your own desired specification.
These boat details are subject to contract.
Note: Offers on the asking price may be considered.